Hawking Technologies HMPS2U Bedienungsanleitung

website www.hawkingtech.come-mail [email protected] © COPYRIGHT 2012 HAWKING TECHNOLOGIES,INC. ALL RIGHTS RESERVED. USER’S MANUALWi

9 Chapter 3 Basic Installation 3.1 Connecting the Hardware 1. Make sure that your USB devices are switched off and that the Server’s Powe

10 3.2.4 Server Names and Server Name Rules The default server name of the Server is “HMPS2U”. If you put two or more Servers in your local area

11 4. Double click the highlighted server (or click the “Configure Server” button. This will open a web browser showing the web interface of

12 6. Click the button corresponding to your choice of IP setting methods (static or dynamic using DHCP). When assigning a static IP address yo

13 Chapter 4 Using the HMPS2U 4.1 Introduction The goal of this product is to provide network support for USB devices. We developed a new t

14 4.4 Installation of a USB Device Some USB devices, like printers or MFPs (multifunction printers), require you to install manufacturer prov

15 G. Now, the installation program will detect the USB device and continue to install driver. H. After the installation is completed, click t

16 4.5 Auto-Connect Printer The method described in section 4.4 is called manual-connect, which means users must manually connect the USB prin

17 D. Choose the desired printer. The desired printer must be the Windows printer (this is a logical printer) that matches the printer attached

18 F. Try to issue a print job to the desired printer. You will see the HMPS2U will automatically do a connect operation and allow you to pri

1 COPYRIGHT Copyright ©2012 by Hawking Technologies, Inc. All rights reserved. No part of this publication may be reproduced, transmitted, transc

19 C. Click the “Network Scanner” button. Note: On Mac, the “Network Scanner” button is denoted by You should see that the HMPS2U will aut

20 E. Follow the usual steps to do scanning. F. After the scanning, close the “Auto-Connect Scanner” window. 4.7 USB Storage You must use

21 Select the Mass Storage device and after Windows installs a driver, you should see the storage icon in the system tray. On Mac, the disk w

22 At this moment, the user on the other computer currently connected to the HMPS2U will see the following window: The user will choose to ac

23 B. Only one PC can get the ownership of the same USB device at the same time. 4.11 Apple Airplay™ Enjoy music from your iTunes library wit

24 Streaming music stored in iPhone, iPod touch, or iPad directly to the HMPS2U If you update your “iPhone/iPod touch/iPad” to iOS 4.3 or later

25

26 Chapter 5 The Server’s Web Pages 5.1 Introduction The HMPS2U has a web user interface. Users may use the web pages to see the HMPS2U’s

27  Network Status  Server Name: the network name of the HMPS2U  Storage Access Mode: which storage mode the HMPS2U is in  IP Address:

28  Wireless Status  Station Name: Mac address of device  SSID: Wireless name of network  BSSID: Mac Address of connected AP  Channel N

2 Federal Communication Commission Interference Statement FCC Part 15 This equipment has been tested and found to comply with the limits for a Cl

29 5.2.2 Setting up Server Configuration To set up the Server configuration, click on the “CONFIG” icon ad then the system will request user to

30  Wireless: You can make your wireless settings for the HMPS2U here.  Basic: Choose you wireless network type, infrastructure (if connect

31  WPS: You can click the WPS button for quick connect if your wireless network supports it. Press enter to go into the settings. PBC is fo

32  Administrator: You can change administrator name and password. If you forgot administrator name and password, you must perform Restore F

33 You can also setup user accounts for your USB hard drives/flash drives. Type in a username and password and set the permission to read, read/

34

35 Chapter 6 Troubleshooting This chapter provides useful information to help you resolve difficulties that you may experience with your Serv

36 Chapter 7 Restore Factory Defaults You may restore the HMPS2U default parameters by one of the following methods. 7.1 Using the Server’s

37 General Information  Server Name: HMPS2U TCP/IP  Automatically get IP by DHCP: Enabled  Static IP: Disabled - IP Address: 192.168.1.100

38 Chapter 8 Upgrade Firmware This chapter describes how to upgrade firmware. Please follow one of the following Procedures: Procedure A: U

3 R&TTE Compliance Statement This equipment complies with all the requirements of DIRECTIVE 1999/5/EC OF THE EUROPEAN PARLIAMENT AND THE COU

39 Chapter 9 The Init Button The Init button is used for maintenance: Simultaneously press Init button and turn on (by plugging in the power

4 Table of Contents CHAPTER 1 INTRODUCTION ... 6 1.1 What is described in this Manual ...

5 CHAPTER 7 RESTORE FACTORY DEFAULTS ... 36 7.1 Using the Server’s Web Pages ...

6 Chapter 1 Introduction Thank you for purchasing the HMPS2U Wireless-N Multifunction USB Device Server (in the following referred to as “Serve

7 Chapter 2 Product Overview 2.1 Package Contents Verify that nothing is missing from the package by using the checking list below. Please

8  USB Indicator is lit when a USB device connects to a USB Port of this Server. 2.4 Supported USB Devices The HMPS2U supports the followi